Toggle Nav
My Cart
Menu
Account
main product photo

M10 x 16mm x 1.4mm Zinc Schnorr® Type VS Serrated Safety Washers High Tensile DIN EN 10132-4

$5.50
In stock
SKU
71SW1016
  • Buy 2 for $3.00 each and save 45%
  • Buy 5 for $1.60 each and save 71%
  • Buy 10 for $1.00 each and save 82%
  • Buy 20 for $0.60 each and save 89%
  • Buy 30 for $0.54 each and save 90%
  • Buy 50 for $0.36 each and save 93%
  • Buy 75 for $0.30 each and save 95%
  • Buy 100 for $0.26 each and save 95%
  • Buy 200 for $0.23 each and save 96%
  • Buy 500 for $0.20 each and save 96%
  • Buy 1000 for $0.15 each and save 97%
Add to Wish List Add to Compare
  • Original SCHNORR® Safety Washers are in the form of a disc spring but with a trapezoidal cross-section and serrations on both sides. The outer diameter is matched to the head diameter of the pan head and socket head cap screws. For screws of property classes 8.8 and 10.9, higher pretension forces might be necessary. These are covered by our reinforced washers type “VS”. Due to the conical form, optimal traction is achieved at highest positive locking due to the helical gearing
  • Schnorr® offer the following advantages: High resistance to vibration due to positive locking of the serrations > Concentrical force transmission and uniform axial load eliminate bending torques and deformation of the bolt stem > The design of the serrations prevents friction and damage to components when tightening > Extremely high safety against loss of pretension force and loosening > Wide variety for materials and different finishes > The closed ring form results in high degree of pretensioning, while avoiding burst-open effect > Development and design of the washers take place on the basis of the screw geometrics, tightening torque as well as the constructive circumstances
  • Understanding and measuring washer sizing: Washer sizes can be a little confusing so we will do our best to try to make it a little easier to understand. When searching for a washer, firstly, let's say you have a M6 bolt and you want a matching washer, look for washers with M6 at the beginning of the description (you can speed this up by using our "shop by" filters). If you already have a washer and you are trying to match it, measure the inside, then look for a size slightly smaller that your measurement. For example the inside measurement of the washer you measured is approx 6.50mm, you need to look for a M6 washer. If the washer measured 17.25mm internally then you need a M16 Washer. Remember washers are not precision fasteners and variations in sizing do exist and all measurements on our site should only be used as a guide
  • Understanding and measuring washer sizing: Washer sizes can be a little confusing. M6 suits a M6 bolt. The inside diameter of a M6 washer is greater than 6mm to allow the washer to fit over the bolt
  • Are Metric & Imperial Washers Interchangeable?: In most cases they are which is why we have added metric sizing to the imperial range and imperial sizing to the metric range. If you are still unsure or if the washer dimensions are critical click on the washer you are interested in and view the technical specifications table before ordering
  • Dimensions: Our stock is genuine Snchnorr® product, sourced from Hobson Engineering, the Australian Distributor. Although the supply is consistent differences may exist between batches such as inside dimensions, outside thickness, visible stamping, appearance, packaging and actual finish
  • Material / Coating: Zinc Plated is the most common fastener of plating due to its the low cost and shinny bright silver finish. A thin layer of zinc is applied by either electroplating or mechanically. It is intended to be used internally as it only offers an average level of protection against corrosion. Whilst some people use it externally it isnt recommended if corrosion is a concern. If you want a fastener that will withstand the outdoor elements choose from our either our Stainless steel or Delta Protekt range of Nord-Lock Washers
  • Measurements: Every effort has been made to ensure all measurements on our site are accurate and where possible to the relevant standard, however they should only be used as a guide. If you have an exact requirement or you see a problem with our specifications please contact us directly
  • Dimensions: Differences can exist between batches such as the inside dimension, outside diameter, thickness, visible stamped markings, appearance and actual finish
  • Photos: represent the product, not the size. Our title has industry sizing but if additional information is required refer to the CAD drawing, Specifications Table or Technical Specifications PDF
  • Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
  • PDF data sheet: The attached PDF data sheets are provided by the manufactuer as a reference guides, specifications may change without notice
  • Note: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, ©Bolt and Nut Australia has made a determined effort to present it accurately
  • Buy with confidence: ⇒ 11+ years experience selling online, > 20,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
  • Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
More Information
More Information
System of Measurement Metric
Product Schnorr® Type VS Serrated Safety Washer
Industry Size M10 x 16 x 1.4
Size M10 (10mm)
To Suit Fastener Size M10
Corrosion Protection Level Moderate
Class / Grade High Tensile Grade 10.9
Material High Tensile Steel
Finish Zinc Plated
Inside Dimension (id) 10.50mm
Outside Dimension (od) 16.00mm
Unloaded Washer Height (h) 1.50 - 2.00mm
Thickness (t) 1.40mm
Tightening Torque (Nm) 8.8 bolt = 59.4, 10.9 bolt = 86.9
OEM Part Number 451 150
Dimensional Data Provided as a guide, subject to change
Standard Made To DIN EN 10132-4
Brand Schnorr®
Alternative Brands Hobson Engineering
We found other products you might like!
  1. M10 x 1.25p Metric Fine Zinc Hex Bolts Class 8.8 High Tensile AS 1110.1
    M10 x 1.25p Metric Fine Zinc Hex Bolts Class 8.8 High Tensile AS 1110.1
    As low as $5.00 Regular Price $5.50
  2. M10 x 1.50p Metric Coarse Zinc Hex Set Screw / Hex Bolts Class 8.8 High Tensile AS 1110.1
    M10 x 1.50p Metric Coarse Zinc Hex Set Screw / Hex Bolts Class 8.8 High Tensile AS 1110.1
    As low as $5.00 Regular Price $5.50
  3. M10 x 1.50p Metric Coarse Zinc Class 12.9 Button Head Socket (6mm Key) Screws ISO 7380
    M10 x 1.50p Metric Coarse Zinc Class 12.9 Button Head Socket (6mm Key) Screws ISO 7380
    As low as $7.00
  4. M10 x 1.50p Metric Coarse Zinc Class 12.9 Countersunk Head Socket (6mm Key) Screws DIN 7991
    M10 x 1.50p Metric Coarse Zinc Class 12.9 Countersunk Head Socket (6mm Key) Screws DIN 7991
    As low as $9.00
  5. M10 x 1.50p Metric Coarse Zinc Class 12.9 Socket (8mm Key) Head Cap Screws DIN 912
    M10 x 1.50p Metric Coarse Zinc Class 12.9 Socket (8mm Key) Head Cap Screws DIN 912
    As low as $6.00
  6. M10 x 1.25p Metric Fine Zinc Hex Set Screw / Hex Bolts Class 8.8 High Tensile AS 1110.1
    M10 x 1.25p Metric Fine Zinc Hex Set Screw / Hex Bolts Class 8.8 High Tensile AS 1110.1
    As low as $5.00 Regular Price $5.50