M10 x 1.25p Metric Fine Zinc Hex Bolts Class 8.8 High Tensile AS 1110.1
As low as
$5.00
Regular Price
$5.50
In stock
SKU
51HF10125_configurable
- Hex Bolts has a hexagon head, part thread and part shank and is used to fasten material. Used to fasten objects together by inserting the bolt from the one end and securing it with either a nut on the other end or into a taped hole. A nut and bolt combination compresses everything together. To tighten the nut requires a socket and wrench or a spanner, If, while tightening the nut, the bolt turns with it, a second spanner or wrench is required to hold-on to the bolt while the nut is tightened. If thread length is critical there is a cross over where a hex bolt could be fully threaded. This is due to a gradual change in the fastener industry due to wholesalers wanting to reduce their stock holdings, now they only carry the shorter lengths as fully threaded. Therefore, if thread length is critical, always check our specifications or contact us prior to ordering
- A guide to determining the approx. thread length, please use as reference only: upto and including 125mm = 2 x diameter + 6mm, over 125mm up to and including 200mm = 2 x diameter + 12mm, over 200mm = 2 x diameter + 25mm
- Material / Coating: Zinc Plated is the most common fastener of plating due to its the low cost and shinny bright silver finish. A thin layer of zinc is applied by either electroplating or mechanically. It is intended to be used internally. Whilst some people use it externally it isnt recommended if corrosion is a concern. If you want a fastener that will withstand the outdoor elements choose from our Stainless steel range
- Material Strength: Bolts are made to class strength 8.8. They have a min yield strength of 640 and a min tensile strength is 800 Mpa
- Thread Pitch (Metric): Pitch means the distance between the peaks of two threads along a screw, bolt, or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Fastener Length: Is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
- A guide to determining the approx. thread length, please note this is only a guide: upto and including 125mm = 2 x diameter + 6mm, over 125mm up to and including 200mm = 2 x diameter + 12mm, over 200mm = 2 x diameter + 25mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, height, width, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: Include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Hex Head Bolt |
| Head Type | Hex Head |
| Size | M10 (10mm) |
| Size & Thread Pitch | M10 x 1.25p Fine |
| Thread Pitch | 1.25mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Fine |
| Corrosion Protection Level | Moderate |
| Class / Grade | High Tensile Class 8.8 |
| Material | Carbon Steel |
| Finish | Zinc Plated |
| Length (l) | Select from the dropdown |
| Thread Length (t) | Choose your length to view |
| Product Diameter (d) | 9.78 - 10.00mm |
| Thread Length | Choose your length to view |
| Across Flats (af) | 15.73 - 16.00mm |
| Across Corners (ac) | 17.77 - 18.40mm |
| Head Height (h) | 6.22 - 6.58mm |
| Spanner Size | 16mm |
| Drive Type | Hex |
| Closest size in imperial | 3/8" |
| Standard Made To | AS1110.1 |
| Brand | Hobson Engineering |
| Alternative Brands | Brighton Best | Bremick Fasteners |
We found other products you might like!
