M10 x 1.50p x 10.8mm Metric Coarse Stainless A2-70 G304 Slab Tee Nut
$8.00
In stock
SKU
41TSS10
- Buy 2 for $6.00 each and save 25%
- Buy 5 for $5.00 each and save 38%
- Buy 10 for $4.20 each and save 48%
- Buy 20 for $3.80 each and save 53%
- Buy 30 for $3.30 each and save 59%
- Buy 50 for $3.00 each and save 63%
- Buy 75 for $2.50 each and save 69%
- Buy 100 for $2.30 each and save 71%
- Buy 200 for $2.10 each and save 74%
- Buy 500 for $1.90 each and save 76%
- Buy 700 for $1.60 each and save 80%
- Buy 1000 for $1.40 each and save 83%
- Buy 2000 for $1.30 each and save 84%
- Slab tee nuts are an useful threaded insert regulary used in the playground industry, fixings in public locations and trains, buses and trucks
- Features / Benefits:
- Tamper Proof: No drive recess for added security
- Large base flange for soft materials - avoids the use of a washer
- Rounded shoulder (threaded section) providdes tamperproof security
- Can be welded to sheet metal
- Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. Most products can be identified by the following markings: A2, A2-70, 304 or G304 but not all nuts are stamped. Stainless steels are largely non-magnetic but it is common for some stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Galling: can occur when excessive pressure is used to tighten a nut onto a thread, common with stainless fasteners but can also be an issue with other materials. Fasteners with damaged or fine threads are particularly prone to galling.
Some suggestions to help prevent thread galling:
Tightening the nut more slowly without excessive pressure, will frequently reduce or sometimes solve completely, the problem. As the installation RPM speed increases, the heat generated with friction during tightening escalates the chances of thread galling.
Reduce the friction by applying a suitable lubricant to the thread frequently eliminates thread galling. Typical lubricants are chloride-paraffine, molykoat lacquer, molybdenum disulphide, high pressure oil, graphite, mica, or talc, some assemblies where there is extreme pressure, corrosion resistant grease or waxes may also be effective - Thread Pitch (Metric): is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, height, width, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Slab Tee Nut |
| Size | M10 (10mm) |
| Size & Thread Pitch | M10 x 1.50p Coarse |
| Thread Pitch | 1.50mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | A2-70 G304 |
| Material | Stainless Steel |
| Flange Thickness (h) | 2.10mm |
| Width (w) | 17.60mm |
| Body Diameter (n) | 11.22mm |
| Nut Height Overall (b) | 10.78mm |
| Nut Length (l) | 25.00mm |
| Barrel Length (l) | 8.36mm |
| Closest size in imperial | 3/8" |
| Brand | Hobson Engineering |
We found other products you might like!
