8g (4.20mm) Zinc Yellow Countersunk (PH2) Coarse Villaboard Timber Screws
$7.00
In stock
SKU
07V8_configurable
- Villaboard Screws are self embedding and designed for fixing fibre cement sheeting to thin gauge steel substrates (up to 0.75mm thick) and timber framing. The ribbed underside of the head allows the screw to easily countersink without mushrooming the fibre cement sheeting. Needle point tip eliminates the need for pre-drilling, saving time during install. Ideal for fixing fibre cement or villa board sheeting to thin steel substrates whilst ensuring a flush finish.
- Material / Coating: Zinc Yellow plated refers to the colour of the chromate that is applied after zinc has been applied. Yellow chromate increases the overall protection of the finish. The coating is intended to be used internally as it only offers an average level of protection against corrosion. If you want a fastener that will withstand the outdoor elements choose look for a Stainless steel or Galvanised fastener
- What does TPI stand for?: TPI stands for “threads per inch” which literally means the number of threads within each inch on a screw, a bolt, or a fastener. To determine the TPI of a screw, count the number of threads contained within an inch of length on the fastener. If the screw is less than an inch count ½” of an inch and multiply by 2
- How to measure the length of a Timber Screw: Fastener length is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
- Thread Length: have been included as a guide only. Due to stock being sourced from multiple suppliers variations do exist. We will always ship the same brand and thread length but subsequent orders may be another brand and the thread length may be different. If thread length is critical, please message us prior to ordering as we are happy to physically check our stock and advise prior to shipping
- Need a Driver Bit?: A large range of suitable driver bits are available in the "Driving" section of our website
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between packaging, visible stamped markings, thread lengths or actual finish
- Photos: are of the product but may not be the actual diameter, length or thread length. Always refer to the technical specifications table for additional information prior to ordering
- Updating our site: If you see any problems with any of our specifications please contact us directly
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Screw Gauge |
|---|---|
| Product | Villaboard Screw |
| Head Type | Countersunk Head Ribbed |
| Nibbed | Yes |
| Underside of Head | Self Countersinking |
| Size | 8g (4.20mm) |
| Thread Pitch | 18 TPI |
| Thread Direction | Right Hand |
| Thread Type | Coarse |
| Corrosion Protection Level | Moderate |
| Class / Grade | Class 2 |
| Material | Carbon Steel SAE 1022 |
| Finish | Zinc Yellow |
| Product Diameter (d) | 4.00 - 4.20mm |
| Head Diameter (a) | 7.90 - 8.10mm |
| Screw Length (l) | Overall length measurement includes head, thread and drill point |
| Head Height (h) | 3.20 - 3.40mm |
| Min to Max Steel Thickness | up to 0.75mm |
| Drive Size | PH2 |
| Screw Point | Needle Point |
| Drive Type | Phillips |
| Recommended Drill Speed | 2500 |
| Closest size in mm | 4.20mm |
| Closest size in imperial | 0.17" |
| Standard Made To | AS3566 |
| Brand | Tower |
| Alternative Brands | Iccons |
We found other products you might like!
