14g (6.30mm) Stainless A2-70 G304 Hex Flange (5/16") Coarse T17 Pit Screws Telstra NBN
As low as
$5.50
In stock
SKU
06S141035P_configurable
- Hex Flange Type 17 Pit Screws are used the in telecommunications industry in when working in the cable pits. They are commonly used for the rollout of the NBN network. The Type 17 Self Drilling point is suitable to drill into timber and most plastics. The 5/16" sized Hex flanged head lends to high pull-out strength. The special long sharp self drilling point with a flute (Type 17) cuts the timber and plastic fibres as it is screwed in. Fibres are collected in the flute and reduce the potential for splitting. The self drilling type 17 point can also pierce light gauge steel up to 0.6mm without predrilling.
- Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. It is highly recommended to use Stainless Steel A4-70 G316 if the product will be used within 300 metres of the coast, in the food and chemical industry or within salt spray affected areas. Most products can be identified by the following markings: A2, A2-70, 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
- What does TPI stand for?: TPI stands for “threads per inch” which literally means the number of threads within each inch on a screw, a bolt, or a fastener. To determine the TPI of a screw, count the number of threads contained within an inch of length on the fastener. If the screw is less than an inch count ½” of an inch and multiply by 2
- How to measure the length of a Timber Screw: Fastener length is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
- Thread Length: have been included as a guide only. Due to stock being sourced from multiple suppliers variations do exist. We will always ship the same brand and thread length but subsequent orders may be another brand and the thread length may be different. If thread length is critical, please message us prior to ordering as we are happy to physically check our stock and advise prior to shipping
- Need a Driver Bit?: A large range of suitable driver bits are available in the "Drilling, Driving and Tools" section of our website
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length, thread length, colour you require, always refer to the size in the description and additional specifications data provided prior to ordering
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Screw Gauge |
|---|---|
| Product | Timber Type 17 Screw |
| Head Type | Hex Flange Head |
| Size | 14g (6.30mm) |
| Thread Pitch | 10 TPI - Coarse |
| Thread Direction | Right Hand |
| Thread Type | Coarse |
| Corrosion Protection Level | Very Good |
| Class / Grade | A2-70 G304 |
| Material | Stainless Steel |
| NEO Sealing Washer | No |
| Product Diameter (d) | 6.20 - 6.40mm |
| Head Diameter (a) | 11.40 - 11.70mm |
| Screw Length (l) | Length measurement is from under head to end of drill point |
| Head Height (h) | 6.60mm |
| Drive Size | 5/16" |
| Screw Point | Type 17 for Timber |
| Drive Type | Hex |
| Single Shear (kN) | 7.2 |
| Axial Tensile (kN) | 12.4 |
| Torsional (Nm) | 11.9 |
| Standard Made To | AS3566 |
| Brand | Hobson Engineering |
| Alternative Brands | Inox World |
We found other products you might like!
