8g (4.20mm) Zinc Yellow Countersunk Wing Phillips (PH2) Coarse Metal Self Drilling Screws
As low as
$5.00
In stock
SKU
08CRW81832_configurable
- Countersunk Head Self Drilling Screws aggressive self embedding head means this screw can be quickly applied without the need to pre-drill or countersink, saving loads of time during application. The two protruding wings create clearance through the timber and break off during entry into the steel.
- Easy to install with a PH2 Phillips screwdriver or PH2 Phillips Driver Bit in a power tool.
- Material / Coating: Zinc Yellow plated refers to the colour of the chromate that is applied after zinc has been applied. Yellow chromate increases the overall protection of the finish. Commonly used in the automotive industry. The coating is intended to be used internally as it only offers an average level of protection against corrosion. If you want a fastener that will withstand the outdoor elements choose from our Stainless steel or Galvanised range
- What does TPI stand for?: TPI stands for “threads per inch” which literally means the number of threads within each inch on a screw, a bolt, or a fastener. To determine the TPI of a screw, count the number of threads contained within an inch of length on the fastener. If the screw is less than an inch count ½” of an inch and multiply by 2
- Length of Thread: Always choose a self driller with enough threads to fully engage in the base metal. For attachments to 1/4" base steel, a self-drilling screw should have at least 1/4" of threads. It is helpful, but not critical, that the threads also engage in the material being fastened. The head of the fastener provides the bearing force for the material being fastened, while the threads provide the clamping force in the base material
- To determine Thread Length: Before buying countersunk screws, it is recommended to work out the overall length you need. Because the overall length includes head height and drill point length you have to add the 2 together then minus that from the overall length to get the approx thread length. For example: a 10g-16 x 35mm countersunk self drilling screw has a 4mm head height and a drill point of approx. 12.50mm. This equals 16.50mm approx, so, on a 35mm long screw you are going to be left with approx. 18.50mm of thread. This detail is often overlooked and it is only when the screws turn up you find they are too short and your project is delayed. All this data along with other specifications is on the specifications table and as always, measurements are approx and do vary between batches and suppliers, if critical always check with us prior
- Drill Point Style: A twist drill style hardened point for fast driving into light gauge sheeting, cladding panels, sections and assemblies. The length of the drilling flutes determine the amount of drilling swaft that can be expelled and therefore the depth of metal can be drilled
- How to measure the length of a Metal Screw: Fastener length is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
- Need a Driver Bit?: A large range of suitable driver bits are available in the "Driving" section of our website
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length, thread length, colour you require, always refer to the size in the description and additional specifications data provided prior to ordering
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Screw Gauge |
|---|---|
| Product | Self Drilling Metal Screw with Wings |
| Head Type | Countersunk Head Ribbed |
| Nibbed | Between 4 - 8 Ribs depending on stock available |
| Size | 8g (4.20mm) |
| Thread Pitch | 18 TPI |
| Thread Direction | Right Hand |
| Thread Type | Coarse |
| Corrosion Protection Level | Moderate |
| Class / Grade | Class 2 |
| Material | Hardened Steel |
| Finish | Zinc Yellow |
| Product Diameter (d) | 4.00 - 4.20mm |
| Head Diameter (a) | 7.70 - 8.10mm |
| Screw Length (l) | Overall length measurement includes head, thread and drill point |
| Head Height (h) | 2.82mm |
| Drill Point Length (p) | 11mm |
| Min to Max Steel Thickness | 1.00 - 2.50mm |
| Drive Size | PH2 |
| Screw Point | Drill Point |
| Drive Type | Phillips |
| Recommended Drill Speed | Under 3000 rpm |
| Material Application | Drill Point c/w Wings |
| Standard Made To | AS3566 |
| Brand | Hobson Engineering |
| Alternative Brands | Tower | Bremick Fasteners |
We found other products you might like!
