14g (6.30mm) x 95mm Surfmist Cyclone BRA / Multiseal Hex Flange (3/8") Metal Roofing Screw Galvanised
$20.00
In stock
SKU
08CY141095C4BRASU
- Buy 5 for $4.00 each and save 80%
- Buy 10 for $3.00 each and save 85%
- Buy 20 for $2.40 each and save 88%
- Buy 50 for $1.40 each and save 93%
- Buy 100 for $1.20 each and save 94%
- Buy 200 for $1.00 each and save 95%
- Buy 500 for $0.90 each and save 96%
- Buy 1000 for $0.80 each and save 96%
- Buy 3000 for $0.70 each and save 97%
- Building code approved Cyclone Rated Metal Screws are suitable in Australia’s most severe cyclonic regions. Ideal for fastening metal roof sheets to metal battens in areas with cyclonic, or high wind conditions that need to withstand extreme wind and vibrational loads. Preassembled with a 25mm BRA plate washer (also known as Multiseal washer) to help prevent water entry and give better load
- Colorbond Painted Head: The head and washer are painted to match to the range of Colorbond® colours.
- Material / Coating: Galvanised coated fasteners have been used for roofing and cladding for over 150 years. Since galvanising was first introduced, we have seen a lot of new terms like Class 3, Class 4, B8, Climaseal 3, Climaseal 4, Climaseal 5, Armour Ceramic Coating, Mechanical Galvanised and Ruspert. They are all variations of the original galvanise. All self drilling and timber T17 screws from Bolt and Nut Australia are guaranteed to comply to a minimum of Class 4 and the ultimate of protection B8. Please refer to our technical pages for more information or contact us for advice on choosing the right fastener
- What does TPI stand for?: TPI stands for “threads per inch” which literally means the number of threads within each inch on a screw, a bolt, or a fastener. To determine the TPI of a screw, count the number of threads contained within an inch of length on the fastener. If the screw is less than an inch count ½” of an inch and multiply by 2
- Length of Thread: Always choose a self driller with enough threads to fully engage in the base metal. For attachments to 1/4" base steel, a self-drilling screw should have at least 1/4" of threads. It is helpful, but not critical, that the threads also engage in the material being fastened. The head of the fastener provides the bearing force for the material being fastened, while the threads provide the clamping force in the base material
- Need a Driver Bit?: A large range of suitable driver bits are available in the "Driving" section of our website
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length, thread length, colour you require, always refer to the size in the description and additional specifications data provided prior to ordering
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Screw Gauge |
|---|---|
| Product | Self Drilling Metal Screw |
| Colour | Surfmist / Off White / Titanium |
| Head Type | Hex Flange Head |
| Size | 14g (6.30mm) |
| Thread Pitch | 10 TPI |
| Thread Direction | Right Hand |
| Thread Type | Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | Class 4 / B8® Cat 5 |
| Material | Hardened Steel |
| Finish | Galvanised |
| Length (l) | 95mm |
| NEO Sealing Washer | BRA = Cyclone Washer |
| Product Diameter (d) | 6.20 - 6.40mm |
| Head Diameter (a) | 24.50 - 25.50mm |
| Screw Length (l) | Length measurement is from under head to end of drill point |
| Head Height (h) | 6.40mm |
| Drill Point Length (p) | 6.60mm |
| Min to Max Steel Thickness | 1.20 - 5.00mm |
| Drive Size | 3/8" |
| Screw Point | Drill Point |
| Drive Type | Hex |
| Single Shear (kN) | 11.1 |
| Axial Tensile (kN) | 20.3 |
| Torsional (Nm) | 20.8 |
| Closest size in mm | 6.30mm |
| Closest size in imperial | 0.25" |
| Standard Made To | AS3566 |
| Brand | Bremick Fasteners |