6mm (M6) Metric Stainless G420 Wave Tooth Spring Roll Pins JIS B 2808:1999
$6.00
In stock
SKU
37SPWS6_configurable
- Wave Tooth Spring Roll Pins are un-headed fasteners used to secure 2 or more parts. The teeth are spaced to interlock when the pin is compressed. This alignment helps retain the roundness of the pin while minimizing lateral movement in vibratory environments to prevent walkout. Slotted toothed pins can serve a dual purpose in certain applications, such as those where both a mechanical stop and a spring retainer is needed. In addition, slotted toothed spring pins can be doubled up for added shear strength by positioning the slots at an angle between 90° and 180° to each other
- Features / Benefits:
- Resuable
- Simple to disassemble with a pin punch or drift pin, will then return to original diameter for re-use
- Light weight
- 30 to 40% lighter than equivalent solid pins
- Fits standard size holes
- Spring pins can suitably replace cold-rolled or taper pins of equal diameter
- Self-locking
- Built-in locking mechanism with spring action
- Also known as: Tension Pins, Roll Pins, Slot Pins, Sel-Loc Pins, S-Lok Pins
- Material / Coating: Stainless Steel G420 is a general purpose basic high hardenability martensitic steel with higher strength, hardness and wear resistance than G410. This is generally used for cutlery and surgical instruments, valves, gears, shafts, cams, shear blades, etc. Under hardened conditions, G420 steels are resistant to fresh water, alkalis, air, foods and mild acids. The corrosion resistance of G420; however, is lower than that of G410, G316 and G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Differences may exist between batches such as visible stamped markings, appearance or actual finish
- Photos: All photos are for illustration purpose only. Actual product or packaging may vary due to product enhancement
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Wave Tooth Spring Pin |
| Size | M6 (6mm) |
| Corrosion Protection Level | Very Good |
| Class / Grade | G420 |
| Material | Stainless Steel |
| Length (l) | Select from the dropdown |
| Pin Diameter | 6.20 - 6.40mm |
| Hole Size to Suit | 6.00mm |
| Wall Thickness (w) | 1.20mm |
| Inside Dimension (id) | 3.80mm |
| Double Shear Load (kN) | 24.83 |
| Closest size in imperial | 15/64" |
| Standard Made To | JIS B 2808:1999 |
| Brand | Hobson Engineering |
We found other products you might like!
