3.2mm (4-5mm Shaft) Stainless G420 E Type Circlip JIS B2805
$6.00
In stock
SKU
37CES3.2
- Buy 2 for $3.50 each and save 42%
- Buy 5 for $1.80 each and save 70%
- Buy 10 for $1.10 each and save 82%
- Buy 20 for $0.60 each and save 90%
- Buy 30 for $0.50 each and save 92%
- Buy 50 for $0.40 each and save 93%
- Buy 100 for $0.24 each and save 96%
- Buy 200 for $0.16 each and save 97%
- Buy 300 for $0.15 each and save 98%
- Buy 500 for $0.13 each and save 98%
- E Type Circlips, also known as retaining rings, have three prongs that fit on shafts or tubes that have grooves on them. They provide a wider shoulder than other external circlips for a larger retaining surface
- How to install: To install use a side-mount e type circlip tool to push them into the groove from the side of the shaft. To choose the correct size measure the shaft and groove diameter. To match an exisiting one measure the outside dimension when uninstalled
- Standard: There are 2 major standards for E Type Circlips JIS B2805 and DIN 6799, we carry JIS B2805, the heavier standard where the circlip thickness is thicker. We can easily source DIN 6799, please ask prior to ordering for availabilty
- Material / Coating: Stainless Steel G420 is a general purpose basic high hardenability martensitic steel with higher strength, hardness and wear resistance than G410. This is generally used for cutlery and surgical instruments, valves, gears, shafts, cams, shear blades, etc. Under hardened conditions, G420 steels are resistant to fresh water, alkalis, air, foods and mild acids. The corrosion resistance of G420; however, is lower than that of G410, G316 and G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, thickness, width, visible stamped markings, appearance or actual finish
- Photos: All photos are for illustration purpose only. Actual product or packaging may vary due to product enhancement
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 11+ years experience selling online, >22,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | E Type Circlip |
| Type | E Type |
| Size | M3.2 (3.2mm) |
| Corrosion Protection Level | Very Good |
| Class / Grade | G420 |
| Material | Stainless Steel |
| Thickness (t) | 0.56 - 0.64mm |
| Shaft Diameter (s) | 4.00 - 5.00mm |
| Circlip Outside Diameter (d) | 6.80 - 7.20mm |
| Groove Size (g) | 3.08 - 3.20mm |
| Groove Width (w) | 0.65 - 0.70mm |
| Closest size in imperial | 1/8" |
| Standard Made To | JIS B2805 |
| Brand | Bolt and Nut Australia |