M16 x 2.00p Metric Coarse Zinc Class 8 Hex Thin Lock Nuts High Tensile AS1112.4
$5.80
In stock
SKU
41L16
- Buy 2 for $3.20 each and save 45%
- Buy 5 for $1.80 each and save 69%
- Buy 10 for $1.20 each and save 79%
- Buy 20 for $0.85 each and save 85%
- Buy 30 for $0.77 each and save 87%
- Buy 50 for $0.60 each and save 90%
- Buy 75 for $0.50 each and save 91%
- Buy 100 for $0.40 each and save 93%
- Buy 200 for $0.37 each and save 94%
- Buy 500 for $0.31 each and save 95%
- Buy 700 for $0.30 each and save 95%
- Buy 1000 for $0.27 each and save 95%
- Buy 2000 for $0.23 each and save 96%
- Buy 5000 for $0.22 each and save 96%
- Hex Thin Lock nuts are also referred to as lock or jam nuts. The correct use of a thin nut is to install it under the larger nut. The thin nut deforms and creates a locking action on the thread as the larger nut is tightened. Therefore the thin nut is more effective when it is soft
- Also known as: Hex Jam Nuts, Jam Lock Nuts, Half Nuts
- Material / Coating: Zinc Plated is the most common fastener of plating due to its the low cost and shinny bright silver finish. A thin layer of zinc is applied by either electroplating or mechanically. It is intended to be used internally. Whilst some people use it externally it isnt recommended if corrosion is a concern. If you want a fastener that will withstand the outdoor elements choose from our Stainless steel range
- Galling: can occur when excessive pressure is used to tighten a nut onto a thread, common with stainless fasteners but can also be an issue with other materials. Fasteners with damaged or fine threads are particularly prone to galling.
Some suggestions to help prevent thread galling:
Tightening the nut more slowly without excessive pressure, will frequently reduce or sometimes solve completely, the problem. As the installation RPM speed increases, the heat generated with friction during tightening escalates the chances of thread galling.
Reduce the friction by applying a suitable lubricant to the thread frequently eliminates thread galling. Typical lubricants are chloride-paraffine, molykoat lacquer, molybdenum disulphide, high pressure oil, graphite, mica, or talc, some assemblies where there is extreme pressure, corrosion resistant grease or waxes may also be effective - Thread Pitch (Metric): is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, height, width, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Thin Lock Nut |
| Size | M16 (16mm) |
| Size & Thread Pitch | M16 x 2.00p Coarse |
| Thread Pitch | 2.00mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Moderate |
| Class / Grade | High Tensile Class 8 |
| Material | Carbon Steel |
| Finish | Zinc Plated |
| Across Flats (af) | 23.67 - 24.00mm |
| Across Corners (ac) | 26.75 - 27.70mm |
| Nut Height Overall (b) | 7.42 - 8.00mm |
| Spanner Size | 24mm |
| Closest size in imperial | 5/8" |
| Standard Made To | AS1112.4 |
| Brand | Hobson Engineering |