M16 x 2.00p Metric Coarse Galvanised Class 8 Hex Thin Lock Nut High Tensile AS1112.4
$5.80
In stock
SKU
41L16G
- Buy 2 for $3.50 each and save 40%
- Buy 5 for $2.00 each and save 66%
- Buy 10 for $1.40 each and save 76%
- Buy 20 for $0.90 each and save 84%
- Buy 30 for $0.80 each and save 86%
- Buy 50 for $0.60 each and save 90%
- Buy 75 for $0.50 each and save 91%
- Buy 100 for $0.40 each and save 93%
- Buy 200 for $0.36 each and save 94%
- Buy 500 for $0.32 each and save 94%
- Buy 700 for $0.30 each and save 95%
- Buy 1000 for $0.28 each and save 95%
- Buy 2000 for $0.24 each and save 96%
- Buy 5000 for $0.22 each and save 96%
- Hex Thin Lock nuts are also referred to as lock or jam nuts. The correct use of a thin nut is to install it between the larger nut and washer. First finger tighten against the washer then wind on the full nut. The thin nut will deform as the full nut is tighten and this creates the locking action on the thread
- Also known as: Hex Jam Nuts, Jam Lock Nuts, Half Nuts
- Material / Coating: Galvanised is a dull greyish colour and can be a little rough in appearance and is mainly used outdoors because of its superior corrosion resistance and proven longevity. Also known as HDG, it is one of the best coatings for protection against rust. Galvanised fasteners have been used across many industries in Australia for over 150 years, roofing, steel buildings, trailers, bridges, fencing, power poles, marina’s, are just a few examples
- Galling: can occur when excessive pressure is used to tighten a nut onto a thread, common with stainless fasteners but can also be an issue with other materials. Fasteners with damaged or fine threads are particularly prone to galling.
Some suggestions to help prevent thread galling:
Tightening the nut more slowly without excessive pressure, will frequently reduce or sometimes solve completely, the problem. As the installation RPM speed increases, the heat generated with friction during tightening escalates the chances of thread galling.
Reduce the friction by applying a suitable lubricant to the thread frequently eliminates thread galling. Typical lubricants are chloride-paraffine, molykoat lacquer, molybdenum disulphide, high pressure oil, graphite, mica, or talc, some assemblies where there is extreme pressure, corrosion resistant grease or waxes may also be effective - Thread Pitch (Metric): is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: All photos are for illustration purpose only and may not represent the actual diameter, height or width require. Actual product or packaging may vary due to product enhancement
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Thin Lock Nut |
| Size | M16 (16mm) |
| Size & Thread Pitch | M16 x 2.00p Coarse |
| Thread Pitch | 2.00mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | High Tensile Class 8 |
| Material | Carbon Steel |
| Finish | Galvanised |
| Across Flats (af) | 23.67 - 24.00mm |
| Across Corners (ac) | 26.75 - 27.70mm |
| Nut Height Overall (b) | 7.42 - 8.00mm |
| Spanner Size | 24mm |
| Closest size in imperial | 5/8" |
| Standard Made To | AS1112.4 |
| Brand | Hobson Engineering |
| Alternative Brands | Bremick Fasteners |