M16 x 2.00p Metric Coarse Bumax 88 High Tensile Stainless A4-80 G316 Hex Standard Nuts DIN 934
$25.00
In stock
SKU
41S16MB88
- Buy 2 for $24.00 each and save 4%
- Buy 5 for $22.00 each and save 12%
- Buy 10 for $21.00 each and save 16%
- Buy 20 for $20.00 each and save 20%
- Buy 30 for $19.00 each and save 24%
- Buy 50 for $18.00 each and save 28%
- Buy 75 for $17.00 each and save 32%
- Buy 100 for $16.00 each and save 36%
- Buy 200 for $15.00 each and save 40%
- Bumax is known as the strongest stainless steel fastener in the world. With the same class properites and strength as carbon steel 8.8 high tensile but with the added benefits of being stainless steel and high corrosion resistance. BUMAX 88 is a premium A4 fastener that also offers far superior corrosion resistance than standard A4 due to its higher molybdenum content
- Features / Benefits:
- Ultimate Corrosion resistance
- High Strength
- Higher yield strength and tighter tolerances
- Fatigue resistance
- Very low magnetic permability
- Manufactured to EN ISO 3506 standards
- Manufactured from a new variant of acid-proof Swedish steel SS 14.234
- Full products have full traceability
- Sourced solely from premium European stainless steel manufacturers according to rigid specifications
- Also known as: Hexagonal Full Nuts, Standard Hex Nuts, Finished Hex Nuts
- Material / Coating: High Tensile Class 8.8 Marine Grade Stainless Steel A4-80 G316 is the ultimate corrosion resistance fastener. Manufactured from a new variant of acid-proof Swedish steel SS 14.234 Bumax Stainless Steel A4-80 G316 can be identified by the unique A4 316 L 80 marking
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Galling: Can occur when excessive pressure is used to tighten a nut onto a thread, common with stainless fasteners but can also be an issue with other materials. Fasteners with damaged or fine threads are particularly prone to galling.
Some suggestions to help prevent thread galling:
Tightening the nut more slowly without excessive pressure, will frequently reduce or sometimes solve completely, the problem. As the installation RPM speed increases, the heat generated with friction during tightening escalates the chances of thread galling.
Reduce the friction by applying a suitable lubricant to the thread frequently eliminates thread galling. Typical lubricants are chloride-paraffine, molykoat lacquer, molybdenum disulphide, high pressure oil, graphite, mica, or talc, some assemblies where there is extreme pressure, corrosion resistant grease or waxes may also be effective - Thread Pitch (Metric): Is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: Represent the product, not the size. Our title has industry sizing but if additional information is required refer to the CAD drawing, Specifications Table or Technical Specifications PDF
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- PDF data sheet: PDF data sheets are provided as a reference guide only. Specifications may change without notice
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 11+ years experience selling online, > 22,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Standard Full Nut |
| Size | M16 (16mm) |
| Size & Thread Pitch | M16 x 2.00p Coarse |
| Thread Pitch | 2.00mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Ultimate |
| Class / Grade | A4-80 High Tensile G316 |
| Material | High Tensile Stainless Steel |
| Across Flats (af) | 23.67 - 24.00mm |
| Across Corners (ac) | 26.75 - 27.70mm |
| Nut Height Overall (b) | 12.30 - 13.00mm |
| Spanner Size | 24mm |
| Closest size in imperial | 5/8" |
| Standard Made To | DIN 934 |
| Brand | Bumax |
| Alternative Brands | Hobson Engineering |