M6 x 1.00p Metric Coarse Nylon Hex Flange NON SERRATED Nuts DIN 6923
$5.80
In stock
SKU
41FLNY6
- Buy 2 for $4.00 each and save 31%
- Buy 5 for $2.00 each and save 66%
- Buy 10 for $1.50 each and save 74%
- Buy 20 for $1.45 each and save 75%
- Buy 30 for $1.40 each and save 76%
- Buy 50 for $1.30 each and save 78%
- Buy 75 for $1.25 each and save 78%
- Buy 100 for $1.20 each and save 79%
- Buy 200 for $1.15 each and save 80%
- Buy 500 for $1.10 each and save 81%
- Buy 700 for $1.00 each and save 83%
- Buy 1000 for $0.95 each and save 84%
- NON Serrated Hex Flange Nuts have a wide flange that acts as a fixed, integrated washer, which helps distribute the pressure of the nut over the part being secured. The non-serrated flange gives some of the benefits of a standard flat washer, saving time and money by removing the need for a washer added to each fastener assembly during installation
- Benefits of Nylon:
- Provides good toughness, tensile strength, non-conductive and resistance to creep, particularly in the high temperature range
- Excellent wear properties, low coefficient of friction and exceptional chemical resistance to aromatic hydrocarbons, greases and oils
- Nylon is a hygroscopic material which tends to absorb water or moisture from the surrounding environment. The amount of absorption will depend on the environmental conditions. When water or moisture is absorbed by Nylon, it behaves like a plasticizer in plastics reducing the tensile strength, stiffness; and increasing elongation, impact strength and energy absorbing characteristics
- Nylon will perform well in long range service in most applications
- Material / Coating: Nylon PA, PA6.6, 66 is the standard polymer used in the Hobson range of fasteners and is recognised worldwide for being the most suitable material for fasteners
- Thread Pitch (Metric): is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Differences may exist between batches such as actual fastener measurements, visible stamped markings, appearance or actual finish
- Photos: All photos are for illustration purpose only and may not represent the actual diameter, height or width require. Actual product or packaging may vary due to product enhancement
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 11+ years experience selling online, > 22,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Flange Nut |
| Size | M6 (6mm) |
| Size & Thread Pitch | M6 x 1.00p Coarse |
| Thread Pitch | 1.00mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | Low Tensile Class 4.6 |
| Material | Nylon |
| Finish | White |
| Across Flats (af) | 9.78 - 10.00mm |
| Across Corners (ac) | 11.05 - 11.50mm |
| Flange Diameter (f) | 12.90 - 13.30mm |
| Nut Height Overall (b) | 5.64 - 6.00mm |
| Hex Height (h) | 5.70 - 6.00mm |
| Serrations under Head | No |
| Spanner Size | 10mm |
| Closest size in imperial | 1/4" |
| Standard Made To | DIN6923 |
| Brand | Hobson Engineering |