M6 x 1.00p Metric Coarse Stainless A2-70 G304 Raised Oval Countersunk Phillips (PH3) Machine Screws DIN 966
$5.00
In stock
SKU
21RCS6_configurable
- Countersunk Raised Oval Phillips Machine Screws can be used to fasten components together by means of through holes and securing with a nut at the other end or they are screwed into a tapped hole with the matching thread. Machine screws are fully threaded and have uniformly threads, meaning they maintain the exact same diameter throughout the entire length of the threaded section of the fastener, unlike self tapping or chipboard screws which have tapered threads. As the name suggests, these screws can be used to fasten components in machines, tools, appliances and electronic devices.
- Also known as: Metal Thread, Stove Bolt, Oval Head, Instrument
- Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. Most products can be identified by the following markings: A2, A2-70, 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Thread Pitch (Imperial):TPI stands for “threads per inch” which literally means the number of threads within each inch on a screw, a bolt, or a fastener. To determine the TPI of a screw, you simply count the number of threads contained within an inch of length. If the screw is less than an inch count upto ½” and x by 2
- Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
- Driver Bits: A large range of suitable driver bits are in the "Driving" section of our website
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions IMPORTANT: Our stock is made to standards DIN 966 and JIS B 1111: 1996, the difference between the 2 standards is the head diameter measurement. If head diameter is critical please check the technical specifications table or contact us prior to placing your order and we can check the stock
- Photos: Are of the product but may not be the actual diameter, head size or length you require, always refer to the size in the description and additional specifications data provided prior to ordering
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: Include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Machine Screw |
| Head Type | Raised Countersunk Head |
| Size | M6 (6mm) |
| Size & Thread Pitch | M6 x 1.00p Coarse |
| Thread Pitch | 1.00mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | A2-70 G304 |
| Material | Stainless Steel |
| Length (l) | Select from the dropdown |
| Thread Length (t) | Full Thread |
| Product Diameter (d) | 5.82 - 6.00mm |
| Head Diameter (a) | 10.57 - 11.70mm |
| Countersunk Angle (ca) | 90° |
| Head Height (h) | 1.50mm |
| Countersunk Height | 3.00mm |
| Drive Size | PH3 |
| Drive Type | Phillips |
| Diameter in Imperial | 1/4" |
| Standard Made To | DIN966 / JIS B 1111 : 1996 |
| Brand | Brighton Best |
| Alternative Brands | Bolt and Nut Australia |
We found other products you might like!
