M6 x 18mm Metric Coarse Zinc Flange Threaded Timber Insert Nuts (6mm Key) Low Tensile
$6.00
In stock
SKU
41TIF618
- Buy 2 for $3.50 each and save 42%
- Buy 5 for $1.80 each and save 70%
- Buy 10 for $1.10 each and save 82%
- Buy 20 for $1.00 each and save 83%
- Buy 30 for $0.90 each and save 85%
- Buy 50 for $0.70 each and save 88%
- Buy 75 for $0.60 each and save 90%
- Buy 100 for $0.48 each and save 92%
- Buy 200 for $0.44 each and save 93%
- Buy 500 for $0.40 each and save 93%
- Buy 700 for $0.38 each and save 94%
- Buy 1000 for $0.36 each and save 94%
- Flange head threaded wood Insert nutshave long teeth that dig deep into wood while being installed preventing turning or pull-out. This creates a very firm strong hold. Threaded inserts are primarily used in two situations. Either the screw has stripped the hole which means the insert will be installed to fix the hole or the user knows the screw will need to be installed and removed often and pre-emptively installs a Hex Drive Threaded Insert to prevent thread damage. Once installed, the insert has metal internal threading that can be continuously installed or removed from the insert without compromising the integrity
- Pilot Hole Recommendations: The data provided was based on testing on Soft Timbers
- MAY NOT BE SUITABLE IN HARDWOODS We have found we get mixed results in hardwoods due to the nature of timber with density and age. testing is required, trying a larger pilot hole or going up a size may be required
- Also known as: Hex Threaded Insert, Threaded Insert Nuts
- Material / Coating: Zinc Yellow plated refers to the colour of the chromate that is applied after zinc has been applied. Yellow chromate increases the overall protection of the finish. The coating is intended to be used internally as it only offers an average level of protection against corrosion
- Thread Pitch (Metric): is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as head diameter, length, body specifications and finish
- Photos: Represent the product, not the size. Our title has industry sizing but if additional information is required refer to the CAD drawing, Specifications Table or Technical Specifications PDF
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- PDF data sheet: PDF data sheets are provided as a reference guide only. Specifications may change without notice
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 11+ years experience selling online, > 22,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Threaded Wood Insert Nut |
| Head Type | Flange Head |
| Works Best On | Softwoods |
| Size | M6 (6mm) |
| Size & Thread Pitch | M6 x 1.00p Coarse |
| Thread Pitch | 1.00mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Moderate |
| Class / Grade | Low Tensile Class 4.6 |
| Material | Zinc Alloy |
| Finish | Zinc Yellow |
| Flange Diameter (f) | 11.40 - 11.90mm |
| Body Diameter (ne) | 8.00 - 8.40mm |
| Body Diameter (n) | 6.90 - 7.30mm |
| Nut Height Overall (b) | 17.70 - 18.10mm |
| Pilot Hole Size | 8.00mm +/- |
| Drive Size | 6mm |
| Drive Type | Internal Hex |
| Closest size in imperial | 1/4" |
| Standard Made To | There is no standard for Timber Insert Nuts |
| Brand | Bolt and Nut Australia |
We found other products you might like!
