10g (4.80mm) Countersunk Square (SQ2) Chipboard Screws Zinc Plated
As low as
$5.50
In stock
SKU
07CBSQ10_configurable
- Chipboard Screws are a coarse thread timber screw with a countersunk flat head and ribs under the head that self embed with the timber surface for a flush or countersunk finish. The screw provides maximum grip and minimum stripout into chipboard, MDF, other composite and soft timbers. It is recommended to drill a pilot hole into some hardwoods so if possible, test on an outcut as performance and outcome vary depending on the type of timber and age. We suggest to choose a screw long enough to provide approx. 20mm of thread embedment into the chipboard or wood being fastened to
- Material / Coating: Zinc Plated is the most common fastener of plating due to its the low cost and shiny bright silver finish. A thin layer of Zinc is applied by either electroplating or mechanically. The coating is intended to be used internally as it only offers an average level of protection against corrosion. If you want a fastener that will withstand the outdoor elements choose from our Stainless steel or Galvanised range
- What does TPI stand for?: TPI stands for “threads per inch” which literally means the number of threads within each inch on a screw, a bolt, or a fastener. To determine the TPI of a screw, count the number of threads contained within an inch of length on the fastener. If the screw is less than an inch count ½” of an inch and multiply by 2
- How to measure the length of a Timber Screw: Fastener length is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
- Thread Length: have been included as a guide only. Due to stock being sourced from multiple suppliers variations do exist. We will always ship the same brand and thread length but subsequent orders may be another brand and the thread length may be different. If thread length is critical, please message us prior to ordering as we are happy to physically check our stock and advise prior to shipping
- Need a Driver Bit?: A large range of suitable driver bits are available in the "Driving" section of our website
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length, thread length, colour you require, always refer to the size in the description and additional specifications data provided prior to ordering
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Screw Gauge |
|---|---|
| Product | Chipboard Timber Screw |
| Head Type | Countersunk Head Ribbed |
| Nibbed | Between 4 - 8 Ribs depending on stock available |
| Size | 10g (4.80mm) |
| Thread Pitch | 8 TPI |
| Thread Direction | Right Hand |
| Thread Type | Coarse |
| Corrosion Protection Level | Moderate |
| Class / Grade | Class 2 |
| Material | Hardened Steel |
| Finish | Zinc Plated |
| Product Diameter (d) | 4.65 - 4.80mm |
| Head Diameter (a) | 8.80 - 9.20mm |
| Screw Length (l) | Overall length measurement includes head, thread and drill point |
| Head Height (h) | 4.40 - 4.60mm |
| Drive Size | SQ2 |
| Screw Point | AB Standard |
| Drive Type | Square |
| Recommended Drill Speed | 1000 |
| Standard Made To | AS3566 |
| Brand | Tower |
| Alternative Brands | Bremick Fasteners |
We found other products you might like!
