M10 x 120mm Metric Coarse Stainless A4-70 G316 Collar Eye Bolt Kit c/w Nut & Washer
$16.00
In stock
SKU
61CEBS10120M
- Buy 2 for $14.00 each and save 13%
- Buy 5 for $13.00 each and save 19%
- Buy 10 for $12.00 each and save 25%
- Buy 20 for $11.00 each and save 31%
- Buy 30 for $10.00 each and save 38%
- Buy 50 for $9.50 each and save 41%
- Buy 100 for $9.00 each and save 44%
- Buy 200 for $8.50 each and save 47%
- Buy 500 for $8.00 each and save 50%
- Eye Bolt Collar Kit is a bolt with a collar and a closed eye at one end. Designed to screw through panels, beams or engineered shade sail structures, used in balustrading and industrial markets. This fitting is not to be used for lifting
- Length: The length measurement for a collar eye bolt length is from under the collar to end of thread (t)
- Testing and Breaking Load: It is the Purchasers responsibility to determine whether the testing procedure and if provided, the breaking load is suitable for purpose
- Material / Coating: Marine Grade Stainless Steel A4-70 G316 is the ultimate corrosion resistance fastener. Designed to be used in all conditions. It is the best material for marine, coastal, chemical and food environments. Stainless steels are largely non-magnetic but it is not uncommon for stainless steel fasteners to show a small degree of magnetism. This is partly due to the work-hardening of the product during the manufacturing process. Marine Grade Stainless Steel A4-70 G316 can be easily identified by the following markings: A4, A4-70, A4-80,316 or G316
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Seizing, Binding or Galling?: All Threads will seize under high tension. It is a well-known and accepted problem especially when using Stainless Steel or other alloys such as aluminium, etc. As pressure builds between the contacting and sliding surfaces protective oxides are broken, possibly wiped off, and interface metal high points shear or lock together. This cumulative clogging-shearing-locking action causes increasing adhesion. In the extreme, galling leads to seizing (the actual freezing together of the threads). If tightening is continued the fastener can be twisted off or its threads ripped out. The frequency of threads seizing can be reduced by using anti-seize compounds, but not eliminated. There are also other ways to minimize the occurrence of thread seizing, Keep the thread clean and away from dirt and grit, etc. Tighten the thread slowly. Work them back and forth occasionally to feel if it is tight when loosening. If the thread starts to feel like it is heating up it is because the metal threads are rubbing against each other under high tension. This can be an early sign that it may seize due to overloading. It may be that you need to go up a size to reduce the overloading. Seizing is not a product fault but is the nature of Stainless Steel material
- Thread Pitch (Metric): Pitch means the distance between the peaks of two threads along a screw, bolt, or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: All photos are for illustration purpose only. Actual product or packaging may vary due to product enhancement
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 11+ years experience selling online, > 22,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Kit Contains | 1x Bolt, 1x Nut & 1x Washer |
| Product | Eye Bolt Collar Kit |
| Head Type | Eye |
| Size | M10 (10mm) |
| Size & Thread Pitch | M10 x 1.50p Coarse |
| Thread Pitch | 1.50mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Ultimate |
| Class / Grade | A4-70 G316 |
| Material | Stainless Steel |
| Length (l1) | 166.00 - 171.00mm |
| Thread Length (t) | 119.00 - 121.00mm |
| Inside Dia. of Eye | 25.00 - 26.00mm |
| Thickness of Eye (e) | 7.30 - 8.00mm |
| Width (a) | 40.00 - 41.50mm |
| Breaking Load Kgs | 2600 |
| Closest size in imperial | 3/8" |
| Brand | Hobson Engineering |