420 Piece M4 M5 M6 M8 M10 M12 Washer + Nut Zinc Assortment Grab Kit21
$48.00
In stock
SKU
KIT21K
- Buy 2 for $41.00 each and save 15%
- Washers assortment grab kit containing a variety of popular sizes of flat washers which are used to distribute the load of a threaded fastener, or as a spacer.
- Handpicked in Brisbane Australia: This kit has been hand picked, assembled and packed with care in our Brisbane warehouse. Packed in a tough clear plastic container, the kit contains some of our most popular sizes designed for service, repair and new installations. Replacement packs are available on our website, in different pack configurations to suit the DIYer to the large manufacturer.
- Quantities in the Kits: The kits are handpicked in-house by our staff, there may be a small variation with the quantities per item due to weight or human error, the overall total number of pieces inside the kit should always exceed the total quantity advertised
- Washer Sizing: The washer size is to suit the corresponding bolt size, it is NOT the inside measurement, e.g M10 x 21 x 1.2 Flat Washer has an inside hole size between approx. 10.50 ~ 10.77mm. This applies to all types of washers, Metric and Imperial
- Material / Coating: Zinc Plated is the most common fastener of plating due to its the low cost and shinny bright silver finish. A thin layer of Zinc is applied by either electroplating or mechanically. It is intended to be used internally. Whilst some people use it externally it isnt recommended if corrosion is a concern. If you want a fastener that will withstand the outdoor elements choose from our Stainless steel range
- Galling: can occur when excessive pressure is used to tighten a nut or bolt onto a thread, common with stainless fasteners but can also be an issue with other materials. Fasteners with damaged or fine threads are particularly prone to galling.
Some suggestions to help prevent thread galling:
Tightening the fastener more slowly without excessive pressure, will frequently reduce or sometimes solve completely, the problem. As the installation RPM speed increases, the heat generated with friction during tightening escalates the chances of thread galling.
Reduce the friction by applying a suitable lubricant to the thread frequently eliminates thread galling. Typical lubricants are chloride-paraffine, molykoat lacquer, molybdenum disulphide, high pressure oil, graphite, mica, or talc, some assemblies where there is extreme pressure, corrosion resistant grease or waxes may also be effective - Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide.
- Photos: Photos are a representation of the product, variations may exists with width, inside diameter, thickness and actual material finish
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as head dimensions, thread lengths visible stamped head markings, appearance or actual finish
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Washer Assortment Kit |
| Kit Type | Washers |
| Size | M4 to M12 |
| Corrosion Protection Level | Moderate |
| Class / Grade | Low Tensile Class 4.6 |
| Material | Mild Steel |
| Finish | Zinc Plated |
| Washer Type | Flat & Nyloc |
| Sizes In Kit | M4,M5,M6,M8,M10,M12 |
| Compatible With | Metric & Imperial Fasteners |
| Nyloc Nut Size and Qty | M4 - 60 Pieces, M5 - 50 Pieces, M6 - 40 Pieces, M8 - 25 Pieces, M10 - 20 Pieces |
| Flat Washer Size and Qty | M4 - 60 Pieces, M5 - 50 Pieces, M6 - 40 Pieces, M8 - 25 Pieces, M10 - 20 Pieces |
| Approx No of Pieces In Kit | 1 Kit contains approx 420 Pieces |
| Packaging | 6 Slot Australian Made Fischer |
| Packaging Dimensions | W195 x D157 x H48mm |
| Country of Origin | Assembled In Brisbane using Overseas Product |
| Brand | Bolt and Nut Australia |