330 Piece M3 M4 M5 M6 M8 M10 M12 Hex + Nyloc Nut Stainless G304 Assortment Grab Kit11
$63.00
In stock
SKU
KIT11K
- Buy 2 for $56.00 each and save 11%
- Nuts assortment grab kit containing a variety of popular sizes of Hex nuts can be used for a variety of fastening tasks that involve a set screw, bolt, machine screw or socket product. Hex Nyloc Nuts replace the need of a lock washer or a nut and cotter pin. Used on the opposite end of a threaded fastener to compress a stack of parts together. Hex shaped to allow fastening and loosening with a spanner or socket.
- Handpicked in Brisbane Australia: This kit has been hand picked, assembled and packed with care in our Brisbane warehouse. Packed in a tough clear plastic container, the kit contains some of our most popular sizes designed for service, repair and new installations. Replacement packs are available on our website, in different pack configurations to suit the DIYer to the large manufacturer.
- Quantities in the Kits: The kits are handpicked in-house by our staff, there may be a small variation with the quantities per item due to weight or human error, the overall total number of pieces inside the kit should always exceed the total quantity advertised
- Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. Most products can be identified by the following markings: A2, A2-70, 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Galling: can occur when excessive pressure is used to tighten a nut or bolt onto a thread, common with stainless fasteners but can also be an issue with other materials. Fasteners with damaged or fine threads are particularly prone to galling.
Some suggestions to help prevent thread galling:
Tightening the fastener more slowly without excessive pressure, will frequently reduce or sometimes solve completely, the problem. As the installation RPM speed increases, the heat generated with friction during tightening escalates the chances of thread galling.
Reduce the friction by applying a suitable lubricant to the thread frequently eliminates thread galling. Typical lubricants are chloride-paraffine, molykoat lacquer, molybdenum disulphide, high pressure oil, graphite, mica, or talc, some assemblies where there is extreme pressure, corrosion resistant grease or waxes may also be effective - Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide.
- Photos: Photos are a representation of the product, variations may exists with width, size, diameter, height or actual material finish
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as head dimensions, thread lengths visible stamped head markings, appearance or actual finish
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Nyloc Nut Assortment Kit |
| Nut Style | Nyloc |
| Kit Type | Nuts |
| Size | M3 to M12 |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | A2-70 G304 |
| Material | Stainless Steel |
| Sizes In Kit | M3,M4,M5,M6,M8,M10,M12 |
| Hex Nut Size and Qty | M3 x 0.50 Pitch - 30 Pieces of each Type, M4 x 0.70 Pitch - 30 Pieces of each Type, M5 x 0.80 Pitch - 30 Pieces of each Type, M6 x 1.00 Pitch - 20 Pieces of each Type, M8 x 1.25 Pitch - 20 Pieces of each Type, M10 x 1.50 Pitch - 20 Pieces of each Type, M12 x 1.75 Pitch - 15 Pieces of each Type |
| Nyloc Nut Size and Qty | M3 x 0.50 Pitch - 30 Pieces of each Type, M4 x 0.70 Pitch - 30 Pieces of each Type, M5 x 0.80 Pitch - 30 Pieces of each Type, M6 x 1.00 Pitch - 20 Pieces of each Type, M8 x 1.25 Pitch - 20 Pieces of each Type, M10 x 1.50 Pitch - 20 Pieces of each Type, M12 x 1.75 Pitch - 15 Pieces of each Type |
| Approx No of Pieces In Kit | 1 Kit contains approx 330 Pieces |
| Drive Type | Hex |
| Packaging | 14 Slot Australian Made Fischer |
| Packaging Dimensions | W195 x D157 x H48mm |
| Country of Origin | Assembled In Brisbane using Overseas Product |
| Brand | Bolt and Nut Australia |