750 Piece M3 M4 Bolt Nut Washer Stainless G316 Assortment Grab Kit29

$99.00
In stock
SKU
KIT29K
  • Buy 2 for $89.00 each and save 10%
  • Hex Bolts assortment grab kit containing a variety of popular sizes of Hex bolts, nuts, nylocs and flat washers.
  • Handpicked in Brisbane Australia: This kit has been hand picked, assembled and packed with care in our Brisbane warehouse. Packed in a tough clear plastic container, the kit contains some of our most popular sizes designed for service, repair and new installations. Replacement packs are available on our website, in different pack configurations to suit the DIYer to the large manufacturer.
  • Quantities in the Kits: The kits are handpicked in-house by our staff, there may be a small variation with the quantities per item due to weight or human error, the overall total number of pieces inside the kit should always exceed the total quantity advertised
  • Washer Sizing: The washer size is to suit the corresponding bolt size, it is NOT the inside measurement, e.g M10 x 21 x 1.2 Flat Washer has an inside hole size between approx. 10.50 ~ 10.77mm. This applies to all types of washers, Metric and Imperial
  • Material / Coating: Marine Grade Stainless Steel A4-70 G316 is the ultimate corrosion resistance fastener. Designed to be used in all conditions. The best fastener for marine, coastal, chemical and food environments. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
  • Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
  • Galling: can occur when excessive pressure is used to tighten a nut or bolt onto a thread, common with stainless fasteners but can also be an issue with other materials. Fasteners with damaged or fine threads are particularly prone to galling.
    Some suggestions to help prevent thread galling:
    Tightening the fastener more slowly without excessive pressure, will frequently reduce or sometimes solve completely, the problem. As the installation RPM speed increases, the heat generated with friction during tightening escalates the chances of thread galling.
    Reduce the friction by applying a suitable lubricant to the thread frequently eliminates thread galling. Typical lubricants are chloride-paraffine, molykoat lacquer, molybdenum disulphide, high pressure oil, graphite, mica, or talc, some assemblies where there is extreme pressure, corrosion resistant grease or waxes may also be effective
  • Helpful Information: Imperial fastenings are referred to as grades, and metric fastenings are referred to as classes. Both have marking systems that make it possible to determine grade and class. An example is a 1/2" UNC bolt with 5 lines on the head is grade 8 and 3 lines is grade 5, both are regarded as high tensile. Metric bolts are slightly different, if it has 4.6 then it is mild steel and 8.8 is high tensile. The markings on a stainless fastener indicate the grade of material and strength, e.g. material G304 grade will have one of the following markings: A2-70, G304, A2, 304 and G316 grade stainless will have one of the following: A4-70, G316, A4, 316
  • How to measure a fastener: Fastener length is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
  • Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide.
  • Photos: Photos are a representation of the product, variations may exists with thread lengths, actual material finish and dimensions
  • Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
  • Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
  • Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as head dimensions, thread lengths visible stamped head markings, appearance or actual finish
  • Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
  • Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
More Information
System of Measurement Metric
Product Hex Bolts Assortment Kit
Head Type Hex Head
Kit Type Hex Bolts
Size M3 to M4
Thread Type Metric - Coarse
Corrosion Protection Level Ultimate
Class / Grade A4-70 G316
Material Stainless Steel
Bolts Supplied Hex Set Screw
Sizes In Kit M3,M4
Nuts Supplied Standard Hex & Nyloc
Washers Supplied Flat
Bolt Size and Quantity M3 x 10 - 25 Pieces, M3 x 16 - 25 Pieces, M3 x 20 - 25 Pieces, M3 x 25 - 25 Pieces, M3 x 30 - 25 Pieces, M4 x 12 - 25 Pieces, M4 x 16 - 25 Pieces, M4 x 20 - 25 Pieces, M4 x 25 - 25 Pieces, M4 x 30 - 25 Pieces
Hex Nut Size and Qty M3 - 50 Pieces, M4 - 50 Pieces
Nyloc Nut Size and Qty M3 - 100 Pieces, M4 - 100 Pieces
Flat Washer Size and Qty M3 x 7 - 100 Pieces, M4 x 9 - 100 Pieces
Approx No of Pieces In Kit 1 Kit contains approx 750 Pieces
Drive Type Hex
Packaging 14 Slot Australian Made Fischer
Packaging Dimensions W195 x D157 x H48mm
Country of Origin Assembled In Brisbane using Overseas Product
Brand Bolt and Nut Australia