9/16" x 12 TPI x 3 Foot (914mm) BSW Coarse Zinc Low Tensile Allthread Threaded Rod IFI 136C
$25.00
In stock
SKU
54W9163
- Buy 2 for $18.50 each and save 26%
- Buy 3 for $15.00 each and save 40%
- Buy 5 for $11.00 each and save 56%
- Buy 10 for $10.00 each and save 60%
- Buy 20 for $7.50 each and save 70%
- Buy 30 for $6.50 each and save 74%
- Buy 50 for $5.70 each and save 77%
- Buy 70 for $4.70 each and save 81%
- Zinc Plated Allthread Threaded Rod is a length of bar with rolled threads allowing internally threaded fittings and nuts to be thread onto the bar and can be used in almost any industry and application
- Common uses: Allthread is commonly used when you cant find a bolt long enough or you need an exact length with full thread. If you only need a certain length a quick and easy way is to wind a nut on, cut the length, then wind the nut off at the end you made the cut, that helps clean the thread. Always use with matching nuts with the same thread pitch
- Also known as: Threaded Rod, Booker Rod, Continous Rod, Threaded Stud
- Material / Coating: Zinc Plated is the most common fastener of plating due to its the low cost and shinny bright silver finish. A thin layer of zinc is applied by either electroplating or mechanically. It is intended to be used internally. Whilst some people use it externally it isnt recommended if corrosion is a concern. If you want a fastener that will withstand the outdoor elements choose from our Stainless steel range
- What does TPI stand for?: TPI stands for “threads per inch” which literally means the number of threads within each inch on a nut, a bolt, or a fastener. To determine the TPI of a nut, either count the number of threads contained within an inch of length on the male fastener or use a thread checker on the nut. If the male fastener is less than an inch count ½” of an inch and x by 2
- Difference between UNC v BSW Threads: UNC and BSW have the same thread per inch value, except for the 1/2" size. Theoretical it would be possible to interchange them as they have the same amount of threads per inch. However due to the difference in thread angle, the connection would not be as strong as when using the proper combinations
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as length, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
- PDF data sheet: The attached PDF data sheets are courtesy of Hobson Engineering. Our preferred supplier of Allthread
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Imperial |
|---|---|
| Product | Allthread |
| Size | 9/16" |
| Size & Thread Pitch | 9/16" x 12 TPI BSW |
| Allthread Length (l) | 3 Foot (914mm) |
| Thread Pitch | 12 TPI |
| Thread Direction | Right Hand |
| Thread Type | UNC / BSW - Coarse |
| Corrosion Protection Level | Moderate |
| Class / Grade | Low Tensile Grade 2 |
| Material | Carbon Steel |
| Finish | Zinc Plated |
| Closest size in mm | M14 (14mm) |
| Standard Made To | IFI 136C |
| Brand | Hobson Engineering |