Pack of 10 - M8 x 1.25p x 3 Metre (3000mm) Metric Coarse Galvanised Low Tensile Allthread Rod DIN 975
$120.00
In stock
SKU
5483G
- Buy 2 for $100.00 each and save 17%
- Buy 5 for $90.00 each and save 25%
- Buy 10 for $80.00 each and save 33%
- Buy 20 for $75.00 each and save 38%
- Buy 30 for $70.00 each and save 42%
- Buy 50 for $65.00 each and save 46%
- Galvanised Allthread is a 3 metre (3000mm) length of bar with rolled threads allowing internally threaded fittings and nuts to be thread onto the bar and can be used in almost any industry and application
- Common uses: Allthread is commonly used in house construction for bracing, cross ties, hanging pipework, electrical tray, fire sprinklers and HVAC systems. Always use with matching nuts with the same thread pitch
- Also known as: Threaded Rod, Booker Rod, Continous Rod, Threaded Stud
- Material / Coating: Galvanised is a dull greyish colour and can be a little rough in appearance and is mainly used outdoors because of its superior corrosion resistance and proven longevity. Also known ASHDG, it is one of the best coatings for protection against rust. Galvanised fasteners have been used across many industries in Australia for over 150 years, roofing, steel buildings, trailers, bridges, fencing, power poles, marina’s, are just a few examples
- Plating thickness of Galvanising: Due to plating thicknesses galvanised and zinc plated threads are not interchangeable. A zinc nut will not wind onto galvanised allthread without damaging the threads and a galvanised nut will be too loose on zinc plated allthread
- Thread Pitch (Metric): is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort hASbeen made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used ASa guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such ASlength, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
- PDF data sheet: The attached PDF data sheets are courtesy of Hobson Engineering. Our preferred supplier of Allthread
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia hASmade a determined effort to present it accurately
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Buy with confidence: ⇒ 11+ years experience selling online, > 22,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| Pack Size | Sold in Packs / Bundles of 10 |
|---|---|
| System of Measurement | Metric |
| Product | Allthread |
| Size | M8 (8mm) |
| Size & Thread Pitch | M8 x 1.25p Coarse |
| Allthread Length (l) | 3 Metre (3000mm) |
| Thread Pitch | 1.25mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | Low Tensile Class 4.6 |
| Material | Carbon Steel |
| Finish | Galvanised |
| Closest size in imperial | 5/16" |
| Standard Made To | DIN 975 |
| Brand | Hobson Engineering |
| Alternative Brands | Bremick Fasteners | Brighton Best |