M12 x 1.25p x 1 Metre (1000mm) Metric Extra Fine Stainless A4-70 G316 Allthread Threaded Rod DIN 975
$50.00
In stock
SKU
54SMF121125M
- Buy 2 for $47.00 each and save 6%
- Buy 3 for $45.00 each and save 10%
- Buy 5 for $43.00 each and save 14%
- Buy 10 for $41.00 each and save 18%
- Buy 20 for $39.00 each and save 22%
- Buy 30 for $37.00 each and save 26%
- Buy 50 for $35.00 each and save 30%
- Stainless Steel Allthread Threaded Rod is a length of bar with rolled threads allowing internally threaded fittings and nuts to be thread onto the bar and can be used in almost any industry and application
- Metric Fine Thread Pitch: Please note this is METRIC FINE THREAD
- Common uses: Allthread is commonly used when you cant find a bolt long enough or you need an exact length with full thread. If you only need a certain length a quick and easy way is to wind a nut on, cut the length, then wind the nut off at the end you made the cut, that helps clean the thread. Always use with matching nuts with the same thread pitch
- Also known as: Threaded Rod, Booker Rod, Continous Rod, Threaded Stud
- Material / Coating: Marine Grade Stainless Steel A4-70 G316 is the ultimate corrosion resistance fastener. Designed to be used in all conditions. The best fastener for marine, coastal, chemical and food environments. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Thread Pitch (Metric Fine): The distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.25mm means that the distance between one thread and the next is 1.25mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as length, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
- PDF data sheet: The attached PDF data sheets are courtesy of Hobson Engineering. Our preferred supplier of Allthread
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Allthread |
| Size | M12 (12mm) |
| Size & Thread Pitch | M12 x 1.25p Extra Fine |
| Allthread Length (l) | 1 Metre (1000mm) |
| Thread Pitch | 1.25mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Fine |
| Corrosion Protection Level | Ultimate |
| Class / Grade | A4-70 G316 |
| Material | Stainless Steel |
| Closest size in imperial | 1/2" |
| Standard Made To | DIN 975 |
| Brand | Hobson Engineering |