Pack of 10 - M8 x 1.25p x 3 Metre (3000mm) Metric Coarse Stainless A2-70 G304 Allthread Rod DIN 975
$250.00
In stock
SKU
54S83
- Buy 2 for $230.00 each and save 8%
- Buy 5 for $210.00 each and save 16%
- Buy 10 for $190.00 each and save 24%
- Buy 20 for $180.00 each and save 28%
- Buy 30 for $170.00 each and save 32%
- Buy 50 for $160.00 each and save 36%
- Stainless Steel Allthread is a 3 metre (3000mm) length of bar with rolled threads allowing internally threaded fittings and nuts to be thread onto the bar and can be used in almost any industry and application
- Common uses: Allthread is commonly used in house construction for bracing, cross ties, hanging pipework, electrical tray, fire sprinklers and HVAC systems. Always use with matching nuts with the same thread pitch
- Also known as: Threaded Rod, Booker Rod, Continous Rod, Threaded Stud
- Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. Most products can be identified by the following markings: A2, A2-70, 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process
- Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material
- Thread Pitch (Metric): is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort hASbeen made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used ASa guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such ASlength, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
- PDF data sheet: The attached PDF data sheets are courtesy of Hobson Engineering. Our preferred supplier of Allthread
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia hASmade a determined effort to present it accurately
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Buy with confidence: ⇒ 11+ years experience selling online, > 22,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| Pack Size | Sold in Packs / Bundles of 10 |
|---|---|
| System of Measurement | Metric |
| Product | Allthread |
| Size | M8 (8mm) |
| Size & Thread Pitch | M8 x 1.25p Coarse |
| Allthread Length (l) | 3 Metre (3000mm) |
| Thread Pitch | 1.25mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | A2-70 G304 |
| Material | Stainless Steel |
| Closest size in imperial | 5/16" |
| Standard Made To | DIN 975 |
| Brand | Hobson Engineering |
| Alternative Brands | Bremick Fasteners | Brighton Best |