M10 x 1.50p x 1 Metre (1000mm) Metric Coarse Nylon Allthread Threaded Rod DIN 975
$52.00
In stock
SKU
54NY101
- Buy 2 for $48.00 each and save 8%
- Buy 3 for $44.00 each and save 15%
- Buy 5 for $42.00 each and save 19%
- Buy 10 for $40.00 each and save 23%
- Buy 20 for $38.00 each and save 27%
- Nylon Allthread is a length of round bar with rolled threads allowing internally threaded fittings and nuts to be thread onto the bar and can be used in almost any industry and application
- Benefits of Nylon:
- Provides good toughness, tensile strength, non-conductive and resistance to creep, particularly in the high temperature range
- Excellent wear properties, low coefficient of friction and exceptional chemical resistance to aromatic hydrocarbons, greases and oils
- Nylon is a hygroscopic material which tends to absorb water or moisture from the surrounding environment. The amount of absorption will depend on the environmental conditions. When water or moisture is absorbed by Nylon, it behaves like a plasticizer in plastics reducing the tensile strength, stiffness; and increasing elongation, impact strength and energy absorbing characteristics
- Nylon will perform well in long range service in most applications
- Material / Coating: Nylon PA, PA6.6, 66 is the standard polymer used in the Hobson range of fasteners and is recognised worldwide for being the most suitable material for fasteners
- Thread Pitch (Metric): is the distance between the peaks of two threads along a screw, bolt, nut or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example, a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as length, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length you may require, always refer to the size in the description and additional specifications data provided prior to ordering
- PDF data sheet: The attached PDF data sheets are courtesy of Hobson Engineering. Our preferred supplier of Allthread
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Buy with confidence: ⇒ 11+ years experience selling online, > 22,000 stock lines, > 100 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Metric |
|---|---|
| Product | Allthread |
| Size | M10 (10mm) |
| Size & Thread Pitch | M10 x 1.50p Coarse |
| Allthread Length (l) | 1 Metre (1000mm) |
| Thread Pitch | 1.50mm |
| Thread Direction | Right Hand |
| Thread Type | Metric - Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | Low Tensile Class 4.6 |
| Material | Nylon |
| Finish | White |
| Ultimate Tensile Load (kN) | 3.2 |
| Tightening Torque (Nm) | 5.6 |
| Closest size in imperial | 3/8" |
| Standard Made To | DIN 975 |
| Brand | Hobson Engineering |