10g (4.80mm) x 25mm Dune Hex Flange (5/16") Metal Self Drilling Cladding Screw Galvanised
$5.00
In stock
SKU
08101625C4DU
- Buy 5 for $1.20 each and save 76%
- Buy 10 for $0.90 each and save 82%
- Buy 20 for $0.80 each and save 84%
- Buy 50 for $0.54 each and save 89%
- Buy 100 for $0.32 each and save 94%
- Buy 200 for $0.20 each and save 96%
- Buy 500 for $0.14 each and save 97%
- Buy 1000 for $0.10 each and save 98%
- Buy 3000 for $0.09 each and save 98%
- Painted Fencing Screws head is painted to match the corresponding colorbond colour. The drill point creates their own hole and thread in one action. The screw is commonly used for carports, sheds, garages, steel framing, fencing and general construction.
- Easy to install using a 1/4" Socket for 8 gauge, 5/16” Socket for 10 and 12 gauge and 3/8” Socket for 14 gauge or appropriate driver bit in a power tool.
- Material / Coating: Galvanised coated fasteners have been used for roofing, cladding, steel buildings, trailers, bridges, fencing, power poles, outdoor furniture, house framing, fencing and marina’s for over 150 years. Since galvanising was first introduced, we have seen a lot of new terms like Class 3, Class 4, B8, Climaseal 3, Climaseal 4, Climaseal 5, Armour Ceramic Coating, Mechanical Galvanised and Ruspert. They are all variations of the original galvanise. All metal self drilling screws from Bolt and Nut Australia are guaranteed to comply to a minimum of Class 3 and extend to Class 4 and the ultimate of protection B8. Please refer to our technical pages for more information or contact us for advice on choosing the right fastener
- What does TPI stand for?: TPI stands for “threads per inch” which literally means the number of threads within each inch on a screw, a bolt, or a fastener. To determine the TPI of a screw, count the number of threads contained within an inch of length on the fastener. If the screw is less than an inch count ½” of an inch and multiply by 2
- Length of Thread: Always choose a self driller with enough threads to fully engage in the base metal. For attachments to 1/4" base steel, a self-drilling screw should have at least 1/4" of threads. It is helpful, but not critical, that the threads also engage in the material being fastened. The head of the fastener provides the bearing force for the material being fastened, while the threads provide the clamping force in the base material
- Thread Length: Thread lengths have been included as a guide only. Due to stock being sourced from multiple suppliers variations do exist. We will always ship the same brand and thread length but subsequent orders may be another brand and the thread length may be different. If thread length is critical, please message us prior to ordering as we are happy to physically check our stock and advise prior to shipping
- Drill Point Style: A twist drill style hardened point for fast driving into light gauge sheeting, cladding panels, sections and assemblies. The length of the drilling flutes determine the amount of drilling swaft that can be expelled and therefore the depth of metal can be drilled
- How to measure the length of a Metal Screw: Fastener length is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. Thus, fasteners with heads that sit above the surface are measured from under the head to the end of the fastener, while fasteners that sit flush with the surface are measured from the top of the head to the end of the fastener
- Need a Driver Bit?: A large range of suitable driver bits are available in the "Driving" section of our website
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: are of the product but may not be the actual diameter, length, thread length, colour you require, always refer to the size in the description and additional specifications data provided prior to ordering
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Screw Gauge |
|---|---|
| Product | Self Drilling Metal Screw |
| Colour | Dune / Birch / Grey |
| Head Type | Hex Flange Head |
| Size | 10g (4.80mm) |
| Thread Pitch | 16 TPI |
| Thread Direction | Right Hand |
| Thread Type | Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | Class 4 / B8® Cat 5 |
| Material | Hardened Steel |
| Finish | Galvanised |
| Length (l) | 25mm |
| NEO Sealing Washer | No |
| Product Diameter (d) | 4.65 - 4.80mm |
| Head Diameter (a) | 11.10 - 11.40mm |
| Screw Length (l) | Length measurement is from under head to end of drill point |
| Head Height (h) | 4.75mm |
| Min to Max Steel Thickness | 0.75 - 3.50mm |
| Drive Size | 5/16" |
| Screw Point | Drill Point |
| Drive Type | Hex |
| Single Shear (kN) | 6.3 |
| Axial Tensile (kN) | 11.1 |
| Torsional (Nm) | 8.3 |
| Closest size in mm | 4.80mm |
| Closest size in imperial | 0.19" |
| Standard Made To | AS3566 |
| Brand | Hobson Engineering |
| Alternative Brands | Tower | Bremick Fasteners |
We found other products you might like!
