1/2" x 12 TPI BSW Coarse Stainless A2-70 G304 Hex Nyloc Nuts NE Series
$6.00
In stock
SKU
41NSW12
- Buy 2 for $4.50 each and save 25%
- Buy 5 for $2.40 each and save 60%
- Buy 10 for $1.60 each and save 73%
- Buy 20 for $1.50 each and save 75%
- Buy 30 for $1.40 each and save 77%
- Buy 50 for $1.30 each and save 78%
- Buy 75 for $1.20 each and save 80%
- Buy 100 for $1.10 each and save 82%
- Buy 200 for $1.00 each and save 83%
- Buy 500 for $0.90 each and save 85%
- Buy 700 for $0.80 each and save 87%
- Hex Nyloc Insert nuts is hex shaped, internally threaded with a nylon insert. The nylon material prevents loosening from vibration and cross threads to stop the nut from backing off of the fastener. The insert deforms elastically over the threads of the screw, but threads are not cut into the nylon. The nylon insert locks the nut in two ways. First, it forces the bottom face of the screw threads against the top face of the nut threads, increasing the friction between the two. Second, the nylon applies a compressive force against the screw itself. They can also be used to assist sealing the bolt thread against seepage of oil, water, petrol, paraffin and other liquids.They come in a variety of materials
- Also known as: Nylon Insert Nut, Nylon Lock Nut
- Material / Coating: Zinc Plated is the most common fastener of plating due to its the low cost and shinny bright silver finish. A thin layer of zinc is applied by either electroplating or mechanically. It is intended to be used internally. Whilst some people use it externally it isnt recommended if corrosion is a concern. If you want a fastener that will withstand the outdoor elements choose from our Stainless steel range
- What does TPI stand for?: TPI stands for “threads per inch” which literally means the number of threads within each inch on a nut, a bolt, or a fastener. To determine the TPI of a nut, either count the number of threads contained within an inch of length on the male fastener or use a thread checker. If the male fastener is less than an inch, measure 1/2", count how many there are then multiply the number by 2
- Difference between UNC v BSW Threads: UNC and BSW have the same thread per inch value, except for the 1/2" size. Theoretical it would be possible to interchange them as they have the same amount of threads per inch. However due to the difference in thread angle, the connection would not be as strong as when using the proper combinations
- Measurements: Every effort has been made to ensure all measurements on our site are accurate and to the relevant standard, they should only be used as a guide. If you see a problem with our specifications please contact us
- Dimensions: Our stock is sourced from various suppliers, therefore differences may exist between batches such as height, width, visible stamped markings, appearance or actual finish
- Photos: All photos are for illustration purpose only and may not represent the actual diameter, height or width require. Actual product or packaging may vary due to product enhancement
- Updating our site: If you see any problems with any of our specifications or you require additional information please contact us
- Disclaimer: Technical data and specifications were researched and compiled from numerous industry sources for the sole purpose of providing basic information. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person, and Bolt and Nut Australia is not responsible for any loss, claim or damages arising therefrom. In developing this information, Bolt and Nut Australia has made a determined effort to present it accurately
- Buy with confidence: ⇒ 10+ years experience selling online, > 19,000 stock lines, > 80 million pieces ex stock in Brisbane QLD
- Prices: include GST, a Tax Invoice and Free Standard Delivery anywhere in Australia
| System of Measurement | Imperial |
|---|---|
| Product | Nyloc Insert Nut |
| Size | 1/2" |
| Size & Thread Pitch | 1/2" x 12 TPI BSW |
| Thread Pitch | 12 TPI |
| Thread Direction | Right Hand |
| Thread Type | BSW - Coarse |
| Corrosion Protection Level | Excellent |
| Class / Grade | A2-70 G304 |
| Material | Stainless Steel |
| Across Flats (af) | 0.736 - 0.750" (18.70 - 19.05mm) |
| Across Corners (ac) | 0.837" (21.26mm) |
| Nut Height Overall (b) | 14.70 - 15.45mm |
| Hex Height (h) | 0.464" (11.79mm) |
| Spanner Size | 3/4" |
| Closest size in mm | M12 (12mm) |
| Standard Made To | NE Series |
| Brand | Hobson Engineering |
| Alternative Brands | Brighton Best |